Artist's impression of SMART-1
|Mission duration||2 years, 11 months, 6 days, 6 hours, 27 minutes, 36 seconds|
|Manufacturer||Swedish Space Corporation|
|Launch mass||367 kilograms (809 lb)|
|Dry mass||287 kilograms (633 lb)|
|Start of mission|
|Launch date||27 September 2003, 23:14:46UTC|
|Launch site||Kourou ELA-3|
|End of mission|
|Decay date||3 September 2006, 05:42:22UTC|
|Periselene||2,205 kilometres (1,370 mi)|
|Aposelene||4,600 kilometres (2,900 mi)|
|Epoch||18 July 2005, 11:14:28 UTC|
|Orbital insertion||15 November 2004|
Legacy ESA insignia for the SMART-1 mission
SMART-1 was a Swedish-designed European Space Agency satellite that orbited around the Moon. It was launched on September 27, 2003 at 23:14 UTC from the Guiana Space Centre in Kourou, French Guiana. "SMART-1" stands for Small Missions for Advanced Research in Technology-1. On September 3, 2006 (05:42 UTC), SMART-1 was deliberately crashed into the Moon's surface, ending its mission.
SMART-1 was about one metre across (3.3 ft), and lightweight in comparison to other probes. Its launch mass was 367 kg or 809 pounds, of which 287 kg (633 lb) was non-propellant.
It was propelled by a solar-powered Hall effect thruster (Snecma PPS-1350-G) using xenon propellant, of which there was 82 kg (50 litres by volume at a pressure of 150 bar) at launch. The thrusters used an electrostatic field to ionize the xenon and accelerate the ions to a high speed. This ion engine setup achieved a specific impulse of 16.1 kN·s/kg (1,640 seconds), more than three times the maximum for chemical rockets. Therefore, 1 kg of propellant (1/350 to 1/300 of the total mass of the spacecraft) produced a delta-v of about 45 m/s. The electric propulsion subsystem had a weight of 29 kg with a peak power consumption of 1,200 watts. SMART-1 is the first in the program of ESA's Small Missions for Advanced Research and Technology.
The solar arrays made 1,190 W available for powering the thruster, giving a nominal thrust of 68 mN, hence an acceleration of 0.2 mm/s² or 0.7 m/s per hour (i.e., just under 0.00002 g of acceleration). As with all ion-engine powered craft, orbital maneuvers were not carried out in short bursts but very gradually. The particular trajectory taken by SMART-1 to the Moon required thrusting for about one third to one half of every orbit. When spiralling away from the Earth thrusting was done on the perigee part of the orbit. At the end of the mission, the thruster had demonstrated the following capability:
- Thruster operating time: 5000 h
- Xenon throughput: 82 kg
- Total Impulse: 1.1 MN-s
- Total ΔV: 3.9 km/s
As part of the European Space Agency's strategy to build very inexpensive and relatively small spaceships, the total cost of SMART-1 was a relatively small 110 million euros (about 170 million U.S. dollars). SMART-1 was designed and developed by the Swedish Space Corporation on behalf of ESA. Assembly of the spacecraft was carried out by Saab Space in Linköping. Tests of the spacecraft were directed by Swedish Space Corporation and executed by Saab Space. The project manager at ESA was Giuseppe Racca and the project manager at the Swedish Space Corporation was Peter Rathsman; the Principal Project Scientist was Bernard Foing.
The Advanced Moon micro-Imager Experiment was a miniature colour camera for lunar imaging. The CCD camera with three filters of 750, 900 and 950 nm was able to take images with an average pixel resolution of 80 m (about 260 ft). The camera weighed 2.1 kg (about 4.5 lb) and had a power consumption of 9 watts.
The Demonstration of a Compact X-ray Spectrometer was an X-ray telescope for the identification of chemical elements on the lunar surface. It detected the x-ray fluorescence (XRF) of crystal compounds created through the interaction of the electron shell with the solar wind particles to measure the abundance of the three main components: magnesium, silicon and aluminium. The detection of iron, calcium and titanium depended on the solar activity. The detection range for x-rays was 0.5 to 10 keV. The spectrometer and XSM (described below) together weighed 5.2 kg and had a power consumption of 18 watts.
The X-ray solar monitor studied the solar variability to complement D-CIXS measurements.
The Smart-1 Infrared Spectrometer was an infrared spectrometer for the identification of mineral spectra of olivine and pyroxene. It detected wavelengths from 0.93 to 2.4 µm with 256 channels. The package weighed 2.3 kg and had a power consumption of 4.1 watts.
The Electric Propulsion Diagnostic Package was to acquire data on the new propulsion system on SMART-1. The package weighed 0.8 kg and had a power consumption of 1.8 watts.
The Spacecraft Potential, Electron and Dust Experiment. The experiment weighed 0.8 kg and had a power consumption of 1.8 watts. Its function was to measure the properties and density of the plasma around the spacecraft, either as a Langmuir probe or as an electric field probe. SPEDE observed the emission of the spacecraft's ion engine and the "wake" the Moon leaves to the solar wind. Unlike most other instruments that have to be shut down to prevent damage, SPEDE could keep measuring inside radiation belts and in solar storms, such as the Halloween solar storms, 2003. It was built by Finnish Meteorological Institute and its name was intentionally chosen so that its acronym is the same as the nickname of Spede Pasanen, famous Finnish movie actor, movie producer and inventor. The algorithms developed for SPEDE were later used in the ESA lander Philae.
Ka band TT&C (telemetry, tracking and control) Experiment. The experiment weighed 6.2 kg and had a power consumption of 26 watts.
SMART-1 was launched September 27, 2003 together with Insat 3E and eBird 1, by an Ariane 5 rocket from the Guiana Space Centre in French Guiana. After 42 minutes it was released into a geostationary transfer orbit of 7,035 × 42,223 km. From there it used its Solar Electric Primary Propulsion (SEPP) to gradually spiral out during thirteen months.
The orbit can be seen up to October 26, 2004 at spaceref.com, when the orbit was 179,718 × 305,214 km. On that date, after the 289th engine pulse, the SEPP had accumulated a total on-time of nearly 3,648 hours out of a total flight time of 8,000 hours, hence a little less than half of its total mission. It consumed about 58.8 kg of xenon and produced a delta-v of 2,737 m/s (46.5 m/s per kg xenon, 0.75 m/s per hour on-time). It was powered on again on November 15 for a planned burn of 4.5 days to enter fully into lunar orbit. It took until February 2005 using the electric thruster to decelerate into the final orbit 300-3,000 km above the Moon's surface. The end of mission performance demonstrated by the propulsion system is stated above.
|Epoch (UTC)||Perigee (km)||Apogee (km)||Eccentricity||Inclination (deg)
(to Earth equator)
|September 27, 2003||~7,035||~42,223||~0.714||~6.9||~10.6833|
|October 26, 2003, 21:20:00.0||8,687.994||44,178.401||0.671323||6.914596||11.880450|
|November 19, 2003, 04:29:48.4||10,843.910||46,582.165||0.622335||6.861354||13.450152|
|December 19, 2003, 06:41:47.6||13,390.351||49,369.049||0.573280||6.825455||15.366738|
|December 29, 2003, 05:21:47.8||17,235.509||54,102.642||0.516794||6.847919||18.622855|
|February 19, 2004, 22:46:08.6||20,690.564||65,869.222||0.521936||6.906311||24.890737|
|March 19, 2004, 00:40:52.7||20,683.545||66,915.919||0.527770||6.979793||25.340528|
|August 25, 2004, 00:00:00||37,791.261||240,824.363||0.728721||6.939815||143.738051|
|October 19, 2004, 21:30:45.9||69,959.278||292,632.424||0.614115||12.477919||213.397970|
|October 26, 2004, 06:12:40.9||179,717.894||305,214.126||0.258791||20.591807||330.053834|
After its last perigee on November 2, on November 11, 2004 it passed through the L1 Lagrangian Point and into the area dominated by the Moon's gravitational influence, and at 1748 UT on November 15 passed the first periselene of its lunar orbit. The osculating orbit on that date was 6,704 × 53,208 km, with an orbital period of 129 hours, although the actual orbit was accomplished in only 89 hours. This illustrates the significant impact that the engine burns have on the orbit and marks the meaning of the osculating orbit, which is the orbit that would be travelled by the spacecraft if at that instant all perturbations, including thrust, would cease.
|Epoch (UTC)||Periselene (km)||Aposelene (km)||Eccentricity||Inclination (deg)
(to Moon equator)
|November 15, 2004, 17:47:12.1||6,700.720||53,215.151||0.776329||81.085||129.247777|
|December 4, 2004 10:37:47.3||5,454.925||20,713.095||0.583085||83.035||37.304959|
|January 9, 2005, 15:24:55.0||2,751.511||6,941.359||0.432261||87.892||8.409861|
|February 28, 2005, 05:18:39.9||2,208.659||4,618.220||0.352952||90.063603||4.970998|
|April 25, 2005, 08:19:05.4||2,283.738||4,523.111||0.328988||90.141407||4.949137|
|May 16, 2005, 09:08:52.9||2,291.250||4,515.857||0.326807||89.734929||4.949919|
|June 20, 2005, 10:21:37.1||2,256.090||4,549.196||0.336960||90.232619||4.947432|
|July 18, 2005, 11:14:28.0||2,204.645||4,600.376||0.352054||90.263741||4.947143|
ESA announced on February 15, 2005, the endorsement of a proposal to extend the mission of SMART-1 by one year until August 2006. This date was later shifted to September 3, 2006, to enable scientific observations from Earth.
SMART-1 impacted the Moon's surface as planned, on September 3, 2006 at 05:42:22 UTC, ending its mission. Moving at approximately 2,000 m/s (4,500 mph), SMART-1 created an impact visible with ground telescopes from Earth. It is hoped that not only will this provide some data simulating a meteor impact, but also that it might expose materials in the ground, like water ice, to spectroscopic analysis.
ESA originally estimated that impact occurred at  In 2017, the impact site was identified from Lunar Reconnaissance Orbiter data at . At the time of impact, the Moon was visible in North and South America, and places in the Pacific Ocean, but not Europe, Africa, or western Asia..
Important events and discoveries
- September 27, 2003: SMART-1 launched from the European Spaceport in Kourou by an Ariane 5 launcher.
- June 17, 2004: SMART-1 took a test image of Earth with the camera that would later be used for Moon closeup pictures. It shows parts of Europe and Africa. It was taken on May 21 with the AMIE camera.
- November 2, 2004: Last perigee of Earth orbit.
- November 15, 2004: First perilune of lunar orbit.
- January 15, 2005: Calcium detected in Mare Crisium.
- January 26, 2005: First close up pictures of the lunar surface sent back.
- February 27, 2005: Reached final orbit around the Moon with an orbital period of about 5 hours.
- April 15, 2005: The search for PELs begins.
- September 3, 2006: Mission ends with a planned crash into the Moon during orbit number 2,890.
- Klesman, Alison (22 Sep 2017). "New observations reveal a lunar orbiter's final resting place". Astronomy Magazine. Retrieved 27 Sep 2017.
- "Probe crashes into Moon's surface". BBC News. September 3, 2006. Retrieved May 23, 2010.
- Kugelberg J.; Bodin P.; Persson S.; Rathsman P. (2004). "Accommodating electric propulsion on SMART-1". Acta Astronautica. 55 (2): 121–130. Bibcode:2004AcAau..55..121K. doi:10.1016/j.actaastro.2004.04.003.
- Foing, Bernard H.; Koschny, D.; Grieger, B.; Josset, J.-L.; et al. "SMART-1 Results and Targets for LRO". NASA. NASA Technical Reports Server. Retrieved 5 October 2011.
- Cornu, N., et al., "The PPS 1350-G Qualification Demonstration: 10500 hrs on the Ground and 5000 hrs in Flight," AIAA Paper 2007-5197, July 2007.
- Swedish Space Corporation
- Josset J. L.; Beauvivre S.; Cerroni P.; De Sanctis M. C.; et al. (2006). "Science objectives and first results from the SMART-1/AMIE multicolour micro-camera". Advances in Space Research. 37: 14–20. Bibcode:2006AdSpR..37...14J. doi:10.1016/j.asr.2005.06.078.
- Basilevsky A. T.; Keller H. U.; Nathues A.; Mall J.; et al. (2004). "Scientific objectives and selection of targets for the SMART-1 Infrared Spectrometer (SIR)". Planetary and Space Science. 52 (14): 1261–1285. Bibcode:2004P&SS...52.1261B. doi:10.1016/j.pss.2004.09.002.
- Di Cara D. M.; Estublier D. (2005). "Smart-1: An analysis of flight data". Acta Astronautica. 57 (2–8): 250–256. Bibcode:2005AcAau..57..250D. doi:10.1016/j.actaastro.2005.03.036.
- Schmidt, Walter; Mälkki, Anssi (2014). "SMART-1 SPEDE: Results and Legacy after 10 Years". 16. Bibcode:2014EGUGA..1613174S.CS1 maint: Uses authors parameter (link)
- Rathsman P.; Kugelberg J.; Bodin P.; Racca G. D.; et al. (2005). "SMART-1: Development and lessons learnt". Acta Astronautica. 57 (2–8): 455–468. Bibcode:2005AcAau..57..455R. doi:10.1016/j.actaastro.2005.03.041.
- SMART-1: On Course for Lunar Capture | Moon Today - Your Daily Source of Moon News Archived 2005-11-02 at the Wayback Machine
- SMART-1 completes its first orbit around the Moon | Moon Today - Your Daily Source of Moon News Archived 2004-12-15 at the Wayback Machine
- ESA Portal - SMART-1 manoeuvres prepare for mission end
- "SMART-1 impacts Moon". European Space Agency. 3 Sep 2006. Archived from the original on 5 September 2006. Retrieved 3 Sep 2006.
- ESA - SMART-1 - Intense final hours for SMART-1
- Kaydash V., Kreslavsky M., Shkuratov Yu., Gerasimenko S., Pinet P., Chevrel S., Josset J.-L., Beauvivre S., Almeida M., Foing B. (2007). "PHOTOMETRIC CHARACTERIZATION OF SELECTED LUNAR SITES BY SMART-1 AMIE DATA". Lunar Planetary Science, XXXVIII, abstract 1535, .
|Wikimedia Commons has media related to SMART-1.|