The first production split-single engine was built from 1918 and the design was used on several motorcycles and cars until the mid 1950s, although one company continued producing split-single engines for motorcycles until 1970. During this time, the design was also occasionally used for engines with four or more cylinders.
Principle of operation
The split-single uses a two-stroke cycle (i.e. where every downward stroke produces power) with the following phases:
- Pistons travel upwards, compressing the fuel-air mixture in both cylinders. A spark plug ignites the mixture (in the right side cylinder in the animation) when the pistons is near the top of the cylinders.
- Pressure from the ignited air-fuel mixture pushes both pistons downwards. Near the bottom of the travel, an exhaust port becomes exposed (in the left side cylinder in the animation), causing the exhaust gases to exit both cylinders. At the same time, the intake port is exposed on the other cylinder, causing a fresh air-fuel mixture (which has been pressurised in the crankcase by the downward movement of the pistons) to be drawn in for the next cycle.
The advantage of the split-single engine compared to a conventional two-stroke engine is that the split-single can give better exhaust scavenging while minimising the loss of unburnt fresh fuel/air charge through the exhaust port. As a consequence, a split-single engine can deliver better economy, and may run better at small throttle openings. A disadvantage of the split-single is that, for only a marginal improvement over a single-cylinder engine, a split-single engine is larger, heavier and more expensive. Since a manufacturer could produce a conventional two-cylinder engine at similar cost to a split-single engine, a two-cylinder engine is usually a more space- and cost-effective design. Most engines used a single combustion chamber (i.e. two cylinders), however some engines used two combustion chambers (i.e. four cylinders) or more.
Initial designs of split-single engines from 1905-1939 used a single Y-shaped or V-shaped connecting rod. Externally, these engines appeared very similar to a conventional single-cylinder two-stroke engine; they had one exhaust, one carburettor in the usual place behind the cylinders and one spark plug.
After World War II, more sophisticated internal mechanisms improved mechanical reliability and led to the carburetor being placed in front of the barrel, tucked under and to the side of the exhaust. An example of this arrangement was used on the 1953-1969 Puch 250 SGS.
Early engines using a "side-by-side" layout (with the carburettor in the "normal" place behind the cylinder) had similar lubrication and pollution problems as conventional two-stroke engines of the era, however the revised designs after World War II addressed these problems.
Pre-World War II examples
The first split-single engine was the Lucas, built in the UK in 1905. It used 2 separate crankshafts connected by gears to drive 2 separate pistons, so that the engine had perfect primary balance.
From 1911-1914, Italian engineer Adalberto Garelli patented a split single engine which used a single connecting rod and long wrist pin which passed through both pistons. Garelli Motorcycles was formed after World War I and produced a 350 cc (21 cu in) split-single motorcycle engine for road use and racing from 1918-1926.
The Trojan two-stroke, as used from 1913 in the Trojan car in the UK, was independently invented but would now be described as a split-single. Photos of a 1927 "twin" model at the London Science Museum show the internals. The "fore-and-aft" layout of the cylinders means that the V-shaped connecting rod has to flex slightly with each revolution. Unlike the German/Austrian motorcycle engines, this engine was water-cooled. The tax horsepower regulations in the United Kingdom resulted in a lower road tax for the Trojan compared with a conventional engine of similar displacement.
Trojan also made another split-single engine later with the cylinders arranged in a 'V' formation. The unusual 'V6' design had two split-single sets of cylinders (4 cylinders total) on one bank of the V and two scavenge blower cylinders on the other bank of the V.[failed verification]
After World War I ended, Austrian industry struggled to recover. Italian engineer Giovanni Marcellino arrived at the main factory of Puch with the instruction to wind up operations. Instead of liquidating the factory, he settled in the town and designed and began production of a new split-single engine which debuted in the 1923 Puch LM racing motorcycle. Influenced by industrial opposed-piston engines, the Puch engine had asymmetric port timing and pistons arranged one behind the other (instead of the side-to-side arrangement used by Garelli). To avoid flexing of the connecting rod, the small-end bearing of the cooler intake piston was arranged to slide slightly fore-and-aft in the piston. In 1931 Puch won the German Grand Prix with a supercharged split-single. By 1935, a four-cylinder version of the Puch split-cylinder design produced 10 kW (14 hp) and was used in motorcycles.
At the 1931 and 1932 Indianapolis 500, Leon Duray's competed with cars powered by the 16-cylinder Duray U16 engine using a split-cylinder design.
In 1935, the Monaco-Trossi Grand Prix car was built with a 16-cylinder radial engine using a split-cylinder design.
Post-World War II Examples
The 1953-1969 Puch 250 SGS (sold in the United States by Sears as the "Allstate 250" or "Twingle") used with an improved system of one connecting rod hinged on the back of the other. These engines typically use the forward piston to control both intake and exhaust ports, with the interesting result that the carburettor is at the front of the engine, under and to the side of the exhaust. The rear piston controls the transfer port from the crankcase to the cylinder. Increasingly, these models were fitted with an oil mixing pump, fed from a reservoir incorporated in the petrol tank. Some also have a twin-spark plug ignition system firing an almost figure-eight shaped combustion chamber. The improvements tamed, if not virtually eliminated, the previous problem of two-stroke plug fouling. A total of 38,584 Puch 250 SGS motorcycles were produced between 1953 and 1970.
Puch ceased production of split-single engines around 1970.
EMC Motorcycles in the United Kingdom manufactured a 350 cc (21 cu in) split-single engine that was used in the 1947-1952 EMC 350. After 1948 the engine also was fitted with an oil pump controlled by the throttle, which dispensed two-stroke oil into the fuel at a variable rate depending on throttle opening, instead of having to pre-mix oil in the fuel.
Triumph-Werke Nürnberg (TWN) in Germany began production of a split-single engines for their motorcycles in 1946. The 250 cc (15 cu in) TWN BDG 250 and 500 cc (31 cu in) TWN BDG 500 models, produced from 1946-1957, used a Y-shaped connecting rod, so the pistons are "side-by-side", making the engine little different visually from a regular two-stroke. Other split-single models from TWN were the 1954-1957 TWN Cornet (200 cc with 12 volt electrics and no kickstart), the 1953-1957 TWN Boss (350 cc) and the 1954-1957 Contessa scooter (200 cc). The bulbous shape of the exhaust of the Cornet and Boss is a two-stroke TWN feature, not linked to the split-single engine. All TWN motorcycle production ceased in 1957.
|Wikimedia Commons has media related to Split-single engines.|
- "Triump TWN". www.classicmotorcycles.org.uk. Archived from the original on 17 January 2012. Cite uses deprecated parameter
- "Split-single torque and economy rival that of a four-stroke". www.sammymiller.co.uk. Cite uses deprecated parameter
- Walker, Mick (11 October 2018). Mick Walker's European Racing Motorcycles. Redline Books. ISBN 9780953131136 – via Google Books.
- "February 1906: The valveless motor car". www.theengineer.co.uk. Retrieved 30 July 2019.
- "Garelli Mosquito". www.ukwheels.com. Archived from the original on 6 May 2012. Cite uses deprecated parameter
- Trojan Two-stroke 1927 Science Museum photo of split-single with V-shaped Connecting Rod.
- "Trojan". www.uniquecarsandparts.com. Retrieved 21 July 2019.
- "Trojan Museum Trust". www.trojanmuseumtrust.org. Retrieved 2016-11-11.
- Walker, Mick (2000), Mick Walker's European Racing Motorcycles, ISBN 9780953131136, retrieved 2011-08-28
- Puch's two-stroke double-piston engines Archived 2007-10-09 at the Wayback Machine asymmetric port opening of 1923 Puch Marcellino design, inspired by industrial opposed-piston engines.
- "Cylinders with two pistons used in motorcycle engine". Popular Mechanics. Hearst Magazines: 843. December 1935. Retrieved 12 July 2019.
- "Triumph TWN". www.classicmotorcycles.org.uk. Archived from the original on 11 February 2012. Cite uses deprecated parameter
- "A Most Remarkable Engine: The Duray U16". www.macsmotorcitygarage.com. 30 January 2016. Retrieved 26 July 2019.
- "Monaco Trossi 1935 Grand Prix Racer". www.oldmachinepress.com. 2 September 2012. Retrieved 26 July 2019.
- "Puch Restorations". www.motorwestmotorcycles.com. Retrieved 27 July 2019.
- "1966 Sears Allstate 250". www.sprynet.com. Archived from the original on 4 November 2018. Cite uses deprecated parameter
- Friedrich F. Ehn: Das große Puch-Buch. Weishaupt, Graz 1993, ISBN 3-900310-49-1 (German). 38,584 Puch 250 SGS were produced from 1953 to 1970.
- "AllstateTwingle". www.mbvmc.org. Retrieved 27 July 2019.
- "1948 EMC 350 - Mark I". www.nationalmcmuseum.org. 5 July 2019. Retrieved 27 July 2019.
- "Old Bike Australasia: Splitting the single - EMC 350cc". www.shannons.com.au. Retrieved 27 July 2019.
- "1957 Isettacarro". www.microcarmuseum.com. Retrieved 27 July 2019.
- "1953 TWN BDG250 - Siamese Twn". www.bsmotoring.com. 27 July 2019. Retrieved 27 July 2019.